Распространенные неисправности и устранение неисправностей мусоровоза с уплотнением мусора isuzu 700P
Распространенные неисправности и устранение неисправностей мусоровоза с уплотнением мусора isuzu 700P
June 07, 2023
Isuzu garbage compactor trucks are important vehicles used for waste management. These Isuzu Garbage compactor trucks are highly efficient and effective in collecting, transporting, and disposing of waste materials. However, like any other vehicle, these isuzu garbage compactor trucks are also prone to breakdowns and require regular maintenance and repair. The most common issues with Isuzu garbage compactor trucks include hydraulic system failure, malfunctioning compacting mechanism, fluid leaks, and electrical system failures. The hydraulic system failure is often characterized by slow or erratic operation of the compactor mechanism. The malfunctioning compacting mechanism can occur due to worn-out bearings, improperly adjusted hydraulic cylinders, or damaged rollers. Fluid leaks from Isuzu garbage compactors may result from damaged hydraulic hoses, seals, or gaskets. Electrical system failures are often due to faulty wiring, blown fuses, or damaged relays. These issues can cause the truck to malfunction, resulting in delays in garbage collection and disposal.
Common Failure and Troubleshooting Oil leakage happened on oil cylinder piston rod 1、The damage of the sealing ring 2、There are scars on the surface of the piston rod 1、Carefully exam the guide sleeve and replace the sealing ring 2、Replace the parts. Piston rod move slowly 1、Some air mixed in the hydraulic cylinder or in the hydraulic oil 2、There are no hydraulic oil in the tank or oil level is too low to work normally. 3、Viscosity of hydraulic oil failing standard 4、Stoppage of the oil inlet/outlet strainer 5、Stoppage or limiting of the hydraulic oil in system 6、Leakage of the oil suction pipe 7、Abrasion of the oil pump 8、Abrasion of some parts 9、Adjustment of the parts are not proper. 10、Pressure valve is too dirty 11、Overload of the system work 12、Improper oil pipe connection 13、Oil pump not work 14、The hydraulic oil temperature is too low 15、The engine’s revolving speed is not enough 1、Eliminate all the air 2、Inject some hydraulic oil and carefully check the system. 3、Replace hydraulic oil to recommended ones. 4、Carefully clean or replace it, and find out the polluted reason 5、Carefully check the oil pipes and clean them. 6、Repair or replace it 7、Repair or replace it 8、Carefully check the pump, valve and oil cylinder, find the abrasion part and repair or replace it. 9、Refer to the technical manual to adjust properly 10、Carefully clean it 11、Refer to the technical manual to load properly. 12、Reconnect the oil pipe properly 13、Carefully check the PTO 14、The viscosity is too high and should be adjust oil temperature to working level 15、Adjust to proper level Hydraulic cylinder pushing is powerless 1、Damage of the piston sealing 2、System pressures is too low (the overflow valve became imbalance) 3、Damage of the oil pump, System pressures is too low 4、Shortage of the hydraulic oil 5、Stoppage of the oil filter 1、Carefully exam and replace the sealing element 2、Carefully exam and adjust the pressure of the overflow valve 3、Carefully exam and replace the oil pump 4、Carefully exam and fulfill the hydraulic oil 5、Carefully exam and replace the filter element Leakage of the oil pump 1、Damage of the sealing filter 2、The oil pipes are not sealed as required 1、Carefully exam and replace the sealing ring 2.1、Carefully exam, tighten the joint 2.2、Replace the joint or add some sealant to seal the joint Blister exist in the hydraulic oil 1、Oil level in the tank is too low 2、There is water in the hydraulic oil 3、Leakage of the pipe between the oil tank and the pump 4、Hydraulic hose is kinked or squished, and limit the flow of the oil 5、Have not choose the right hydraulic oil 6、Abrasion of the sealing parts in oil pump axle 1、Adjust the oil to required level. Carefully exam the leakage of the system. 2、Exchange new hydraulic oil 3、Fasten the joint or exchange suction pipe 4、Replace the oil pipe 5、Exchange to the recommend oil 6、Carefully clean or replace it. Oil pump is too noise while working 1、The hydraulic oil viscosity is too high 2、Speed of the oil pump is too high 3、Suction pipe is blocked or extrusion 4、The oil tank’s respirator is blocked 5、Primary oil filter is blocked 6、Parts sticking to each other 7、There are air in the hydraulic oil 8. Уровень гидравлического масла слишком низкий. 9. Части масляного насоса изнашиваются . 1. Замените масло с низкой вязкостью. 2. Отрегулируйте скорость масляного насоса до требуемого уровня. 3、Очистка или замена всасывающей трубы 4、Откройте респиратор, тщательно промойте его, чтобы очистить. 5、Очистка сетчатого фильтра 6、Тщательно отремонтируйте торчащие детали, очистив их все и при необходимости замените 7、Тщательно проверьте систему, замените всасывающую трубу и уплотнительные детали. 8. Отрегулируйте до нужного уровня . 9. Отремонтируйте масляный насос и выясните причину .
4、Повреждение штока поршня 1、Замените цилиндр и выясните, почему он поврежден 2、Отремонтируйте или замените поршневой клапан, выясните причину 3、Закрепите детали до отсутствия утечек 4、Внимательно осмотрите, замените при необходимости Гидравлическое масло температура слишком высока 1、Используйте регулирующий клапан в течение длительного времени 2、Неподходящее гидравлическое масло 3、Высокая скорость вращения 4、Внутренняя утечка 1、Ручной джойстик должен перемещаться, когда он не используется 2、Замените масло на подходящее 3 、Отрегулируйте до надлежащего уровня 4、Внимательно проверьте насос, клапан и масляный цилиндр, чтобы выяснить причину, затем устраните их.
Для устранения этих проблем квалифицированные механики обычно проводят осмотры, диагностику и ремонт. Они часто начинают с проверки гидравлической системы на наличие поврежденных шлангов, цилиндров или насосов. Затем они проверяют механизм катка на наличие изношенных подшипников, поврежденных роликов и других проблем. Если есть утечка жидкости, они находят источник и заменяют поврежденные уплотнения или прокладки. Наконец, механики проверяют электрическую систему, чтобы устранить любые проблемы с проводкой или компонентами. Если неисправный компонент идентифицирован, они заменяют его подходящей запасной частью. Затем грузовики-уплотнители мусора Isuzu проходят испытания, чтобы убедиться, что все проблемы устранены и грузовик работает эффективно.
В заключение, мусоровозы Isuzu необходимы для утилизации отходов, но они также требуют регулярного обслуживания и ремонта для эффективной работы. Квалифицированные механики часто проводят проверки, диагностику и ремонт этих грузовиков, чтобы выявить и устранить любые проблемы. Надлежащее техническое обслуживание обеспечивает бесперебойную работу и продлевает срок службы этих грузовиков.
Если вы заинтересованы в нашей продукции и хотите узнать более подробную информацию, пожалуйста, оставьте сообщение здесь, мы ответим вам, как только сможем.